✎ lale [skrammelWiki]

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

**STORAGE SYSTEM**

A few years ago, I added my own storage for quilting rulers and protractors to my E2. It was a very simple construction made from leftover fabric and some hook-and-loop fasteners. I wanted to revisit the idea of having removable storage on the sides of the frame, perhaps using snaps, eyelets or hook-and-loop fasteners. The build should be something simple, so that others are able to replicate it if they want to. It might be a good idea to print a template for the construction.

</WRAP>

<WRAP third column>
{{ :20250721_toolsseminar_mockup_light.jpg?direct&700 |}}

</WRAP>
</WRAP>

----

I took inspiration from different bike bags, camping supplies and mountaineering equipment.

<WRAP group>
<WRAP quater column>
{{:inspo_1.jpeg?280 |}}

</WRAP>

<WRAP quater column>
{{:inspo_2.jpeg?280 |}}

</WRAP>

<WRAP quater column>
{{:inspo_4.jpeg?280 |}}

{{:dumpling_inspired_backpack_-_yanko_design.jpeg?280 |}}
</WRAP>

<WRAP quater column>
{{ :attachments.jpeg?280 |}}

{{ :women_s_utility_tool_belt_ltloden.jpeg?280 |}}
</WRAP>
</WRAP>

----

**Planning the grid:**

The entire construction should be easily accessible from a seated position, which is why I decided to make it half the width of an Eiermann frame. You could even attach two next to eachother if needed.

----

**First prototype:**

The first version was made entirely out of fabric. Strips measuring 70 x 750 mm were cut from Köper, halved and ironed to a width of 35 mm. These strips were then arranged in a 5x6 grid and sewn down around all edges to create an overlapping design.

----

**Testing the strength:**

To test the load capacity of the anchor points, I attached a bag to two points and slowly added weights. The first snap clips I used could hold a maximum of 3 kg (so 1.5 kg per each, the final version can hold over 6 kg).

----

**Second prototype:**

Swapped from fabric to seatbelt straps for more stability and changes the snaps since they were not heavy duty enough.

----

**Attachment testing:**

First test of all the closures on a Eiermann Frame.

</WRAP>

<WRAP third column>
<WRAP center round box 95%>
**FINAL VERSION**

Cut the straps into 5x750mm and 7x305mm pieces, glued the ends with planatol bb so they will not unravel (this glue is also very flexible when dry so ideal to sew over).

Then I marked the horizontal pieces in 45 mm  and the vertical pieces in 35 mm increments. I marked the sections with tape.

I sewed all the short pieces onto the outermost piece. Then I continued with the rest using the pattern I made beforehand.

All the tape was removed and then all the connections were reinforced with a zigzag stitch using the contrasting colour each time.

Using a soldering iron I burned 35 holes into each connection point.

Then added the snaps on all rows but the upper and lowest. Adding the top buckles and the hook and loop on the bottom, reinforced the seams and then put in all the remaining snaps.

</WRAP>
</WRAP>

<WRAP third column>
<WRAP center round box 95%>
**MATERIALS USED**
  * 35 Camping and Boating snaps
  * 9m of seatbelt strap in 25mm
  * 5 aluminium G-buckles
  * 50 cm of hooks and loop 
  * Bookbinding glue or woodglue
  * A hammer 
  * Sewing Machine
  * Soldering iron (to make the holes)

</WRAP>

<WRAP center round box 95%>
**Pattern Ideas:**

I tested various configurations of the pattern, but these three were my favourites. They all use roughly the same amount of each colour, except for the one in the middle.
</WRAP>

{{ :20250722_toolsseminar_pattern_v1.jpg?500 |}}
{{ :20250722_toolsseminar_pattern_v2.jpg?500 |}}
{{ :20250722_toolsseminar_pattern_v3.jpg?500 |}}

</WRAP>
</WRAP>

Edit summary

Note: By editing this page you agree to license your content under the following license: Public Domain